Available Sheens: Gloss
Available Colours: Clear, White, Terracotta, Sandstone, Silver Gray and Battleship Gray
Colorant Used: Ready Mixed Colours Only
Colour System Supported: Ready Mixed Colours Only
Cleanup: Xylene
Resin Type: 2-Component Cycloaliphatic Amine Epoxy
Recommended Use: Interior
MPI Rating: N/A
VOC Level: 13 g/L
Products
-
100% Solids Epoxy Floor Coating
V430
Show DetailsHeavy-duty protection from a 100% solids epoxy for demanding industrial/commercial environments exposed to heavy vehicular and pedestrian traffic, constant moisture, intermittent strong chemical spills, and frequent cleaning with chemicals, steam and power washers.
- Self-levelling, high-build 100% solids formula
- Very low VOC
- Tenacious adhesion to concrete
- Outstanding durability
- Smooth gloss finish
- Meets qualifications for LEED as a floor coating
- Suitable for use in USDA inspected facilities
-
100% Solids Epoxy Pre-Primer
V155
Show Details100% Solids Epoxy Pre-Primer is formulated for use on both steel and masonry. For rusted steel where extensive surface preparation is needed, but not logistically possible, the penetrating properties and extended dry time – 16 hours at 25 °C (77 °F) – of this two-component epoxy seal crevices and other imperfections, promoting better adhesion for subsequent coats. For prepared masonry surfaces, V155 penetrates and seals, providing an excellent foundation for subsequent coats of Corotech epoxy floor coatings. The unique, 100% solids formula of V155 forms a sealed epoxy barrier that inhibits future corrosion.
- Low viscosity easily fills voids and crevices
- Does not shrink – eliminates craters
- Chemical and fume resistant
- Extended cure time allows maximum penetration
- Seals previously coated concrete, masonry, and galvanized metal
- Qualifies for LEED certification
-
Acrylic DTM Enamel – Gloss
V330
Show DetailsAcrylic DTM Enamel delivers superior resistance to moisture. This waterborne, all-acrylic finish can be applied direct-to-metal or over primer. The glossy surface is UV resistant, and special inhibitors in the formula prevent flash rusting when the finish is applied to ferrous metal.
- For light-to-moderate industrial exposures
- For metal, wood and masonry substrates
- Flash rust resistant and corrosion protection on ferrous metals
- Excellent for all corrugated metal sheeting
- Meets Performance Requirements of TT-P-1511
-
Acrylic DTM Enamel — Semi-Gloss
V331
Show DetailsAcrylic DTM Enamel is a tough waterborne acrylic enamel that fights rust on metal and provides a smooth, durable finish on wood, drywall and masonry substrates. A special inhibitor in the formula prevents flash rust when applied to ferrous metal, and the smooth dry film is UV and moisture resistant.
- For light-to-moderate industrial, commercial and select residential use
- Excellent for metal, as well as wood, masonry, drywall and other surfaces
- Resists flash rust on metal
- Excellent for all corrugated metal sheeting
- Can be used on galvanized and aluminum metal
-
Acrylic Metal Primer
V110
Show DetailsAcrylic Metal Primer is a water-reducible, rust-inhibitive primer for steel, iron, and non-ferrous metal. It provides excellent adhesion to a range of hard-to-coat surfaces and can even be applied over tightly adhering rust. Designed for light-to-moderate industrial exposures, this product can be top coated with a wide variety of coatings.
- High solids content
- Low odour; suitable for occupied areas
- Can be recoated in just 4 hours
- Suitable for use in USDA-inspected facilities
- Qualifies for LEED certification
-
Aliphatic Acrylic Urethane – Gloss
V500
Show DetailsAliphatic Acrylic Urethane – Gloss is a multi-use, two-component urethane appropriate for use on both metal and masonry. This product provides excellent gloss and colour retention when used on exterior surfaces exposed to sunlight and rain, and the highly cross-linked formula provides superior abrasion, chemical, and solvent resistance. Due to these outstanding features, urethanes are often used as the final layer in a multi-layer system on steel or masonry.
- Resistant to hydraulic fluid
- Outstanding UV protection
- High chemical and abrasion resistance
- Suitable for use in USDA inspected facilities
- Meets performance specs of MIL-C-85285
- Excellent anti-graffiti coating
-
Aliphatic Acrylic Urethane — Semi-Gloss
V510
Show DetailsAliphatic Acrylic Urethane is a multi-use, two-component urethane appropriate for use on both metal and masonry. This product provides excellent gloss and colour retention when used on exterior surfaces exposed to sunlight and rain, and the highly cross-linked formula provides superior abrasion, chemical, and solvent resistance. Due to these outstanding features, urethanes are often used as the final layer in a multi-layer system on steel or masonry.
- Resistant to hydraulic fluid
- Outstanding UV protection
- High chemical and abrasion resistance
- Suitable for use in USDA inspected facilities
- Meets performance specs of MIL-C-85285
- Excellent anti-graffiti coating
-
Alkyd Gloss and Hardness Catalyst
Show DetailsAlkyd Gloss and Hardness Catalyst speeds drying while producing a higher gloss and more corrosion resistance, as well as a harder enamel finish. Other benefits include increased solvent and chemical resistance.
-
Alkyd Urethane EnV200amel – Gloss
V200
Show DetailsV200 product is a heavy-duty alkyd enamel intended for use on a wide variety of surfaces, both interior and exterior. The surface-tolerant formula sticks to surfaces that may be marginally prepared, and the exceptional flow and levelling provides a smooth, uniform finish. Made with our toughest alkyd resin, this paint stands up to mechanical and human abuse, while the urethane fortification adds gloss and colour retention in exterior spaces exposed to sunlight and rain.
- Urethane modification for maximum durability
- Easy application
- For use on all surfaces
- Hard, scratch- and impact-resistant coating
- High-solids formula
-
Anti-Slip Aggregate
V630
Show DetailsThis specially formulated anti-slip aggregate is designed to elevate the foot or wheel on a damp or wet surface, permitting the water to escape instead of causing the foot or wheel to hydroplane.
-
Aromatic Moisture-Cured Urethane
V580
Show DetailsThis coating is a one-component, high-solids, moisture-cured urethane intended for use on floors exposed to moderate to extreme conditions. It provides excellent abrasion, impact resistance and chemical resistance. Exposure to sunlight will cause yellowing.
- 2 hours dry to touch
- Uses moisture in the air to produce a hard cross-linked film
- Quick return to light traffic (8 to 12 hours depending on humidity)
- Suitable for use in USDA inspected facilities
-
Brushing Reducer
V701
Show DetailsBrushing Reducer is a blend of High Flash Naphtha and Mineral Spirits. Use this solvent to improve the brushing characteristics of single-component, solvent-based coatings.
- For use with all alkyd and oil-modified polyurethane coatings
- Effectively cleans tools and equipment
- May be used to reduce and thin coatings up to the legal limits allowed by district
-
Citrus Based Cleaner
V610
Show DetailsCitrus Based Cleaner is an industrial strength, biodegradable, phosphate-free, emulsifying cleaner based on a natural citrus by-product. Cleans metals, masonry, painted surfaces, glass, upholstery, carpets, tile, plastics, and more.
- Concentrated for maximum strength
- Excellent cleaner for a wide variety of surfaces
- Biodegradable and phosphate-free
- Milder and less corrosive to cleaned surfaces
-
Clear Acrylic Sealer
V027
Show DetailsClear Acrylic Sealer is a waterborne, fast drying, clear acrylic coating formulated as an easy-to-apply seal coat on bare concrete floors and other masonry surfaces. This product is designed to allow for easy sweep up of dust and to reduce water penetration or erosion, efflorescence, spalling, and chalking without changing the natural appearance of the substrate. Areas exposed to heavy-duty industrial traffic or severe exterior conditions may require multiple coats.
- Rapid dry
- Soap and water clean-up
- Can be used over a variety of substrates
- Blister and alkali fume resistant
- Low odour
-
Coal Tar Epoxy
V157
Show DetailsCoal Tar Epoxy is a high-solids, two-component tar filled coating formulated to provide excellent film build in one or two coats. The high level of cross-linking provides an excellent barrier coat for immersion service in fresh water, salt water or waste water. Additionally, this product is resistant to many acids, alkalis and mild solvents in splash and spill exposures.
- Formulated for use over properly prepared/primed steel, iron, concrete, and non-ferrous metal
- Provides excellent protection from water, acids, alkalis, and mild solvents
- Can be applied directly to the substrate; use with a primer for extra longevity
- Suitable for use in USDA inspected facilities
- Meets Performance Requirements for Army Corps of Engineers C-200
- Meets Performance Requirements for SSPC Paint 16
- Meets Performance Requirements for DOD-P-23236
-
Concrete & Masonry Etcher
V620
Show DetailsConcrete & Masonry Etcher is used for removing laitance and etching concrete. This pre-treatment includes surfactants that provide better penetration for removing foreign materials and contaminates. It also contains extenders which give a more even etch over larger areas.
- Concentrated for maximum strength
- Inhibitors protect metal surfaces from corrosion
- May be used to remove rust and scale from steel